This chapter describes LAN Emulation Client Functions (LEC) messages. For information on message content and how to use the message, refer to the Introduction.
| LEC.001 |
Level: C-INFO
Short Syntax: LEC.001 LEC function entry/exit tracing
Long Syntax: LEC.001 LEC function entry/exit tracing
Description: The user can enable/disable the function entry and exit tracing of the LEC by simply turning on/off the display of this message.
| LEC.002 |
Level: C-INFO
Short Syntax: LEC.002 nt network entry_exit log_point
Long Syntax: LEC.002 network network: lec trace log: entry_exit log_point
Description: LEC generic function entry/exit
| LEC.003 |
Level: C-INFO
Short Syntax: LEC.003 nt network entry_exit log_point, D1= arg1
Long Syntax: LEC.003 network network: lec trace log: entry_exit log_point, D1= arg1
Description: LEC generic function entry/exit with one arg
| LEC.004 |
Level: C-INFO
Short Syntax: LEC.004 nt network entry_exit log_point, D1= arg1, D2= arg2
Long Syntax: LEC.004 network network: lec trace log: entry_exit log_point, D1= arg1, D2= arg2
Description: LEC generic function entry/exit with two args
| LEC.006 |
Level: C-INFO
Short Syntax: LEC.006 nt network trace_type log_point, conn_handle= conn_handle
Long Syntax: LEC.006 network network: lec trace log: trace_type log_point, conn_handle= conn_handle
Description: LEC generic trace msg with one arg - a conn handle
| LEC.007 |
Level: C-INFO
Short Syntax: LEC.007 nt network trace_type log_point, client_state= client_state
Long Syntax: LEC.007 network network: lec trace log: trace_type log_point, client_state= client_state
Description: LEC generic trace msg with one arg - the client state
| LEC.008 |
Level: UE-ERROR
Short Syntax: LEC.008 LEC inbnd fr dscrd, bad FC, on nt network ID, word1 word2 word3 word4
Long Syntax: LEC.008 LEC inbnd fr dscrd, bad FC, on network network ID, word1 word2 word3 word4
Description: LEC inbound data frame was discarded - bad FC byte
| LEC.009 |
Level: U-INFO
Short Syntax: LEC.009 nt network LEC state chng from old_state to new_state
Long Syntax: LEC.009 network network LEC client state machine changed from old_state to new_state
Description: The LEC client state machine (CLSM) keeps track of which state the LEC is currently in. The possible states are: IDLE, LECS_SETUP, CONFIGURE, LES SETUP, JOINING, ARPING FOR BUS, BUS SETUP, and OPERATIONAL.
| LEC.010 |
Level: U-INFO
Short Syntax: LEC.010 nt network dest state chng from old_state to new_state
Long Syntax: LEC.010 network network LEC destination state machine changed from old_state to new_state
Description: The LEC destination machine (DSM) keeps track of what state the ARP entry is in. The possible states are: UNKNOWN, ARPING, CYCLING, KNOWN, FLUSHING, and CONNECTED.
| LEC.011 |
Level: P_TRACE
Short Syntax: LEC.011 Trace LEC data packet
Long Syntax: LEC.011 Trace LEC data packet
Description: Trace LEC data packet
| LEC.012 |
Level: P_TRACE
Short Syntax: LEC.012 Trace LEC control packet
Long Syntax: LEC.012 Trace LEC control packet
Description: Trace LEC control packet
| LEC.013 |
Level: C-TRACE
Short Syntax: LEC.013 nt network Rcvd ctrl_frame on conn handle conn_handle with xid xid
Long Syntax: LEC.013 network network Received ctrl_frame control frame on conn handle conn_handle with tran id of xid
Description: The LEC received a control frame from the ATM network
| LEC.014 |
Level: C-TRACE
Short Syntax: LEC.014 nt network Sent ctrl_frame on conn handle conn_handle with xid xid
Long Syntax: LEC.014 network network Sent ctrl_frame control frame on conn handle conn_handle with tran id of xid
Description: The LEC sent a control frame over the ATM network
| LEC.015 |
Level: U-INFO
Short Syntax: LEC.015 nt network trace_type log_point
Long Syntax: LEC.015 network network: lec trace log: trace_type log_point
Description: lec general information
| LEC.017 |
Level: U-INFO
Short Syntax: LEC.017 nt network trace_type log_point, D1= arg1, D2= arg2
Long Syntax: LEC.017 network network: lec trace log: trace_type log_point, D1= arg1, D2= arg2
Description: lec general information with two args
| LEC.020 |
Level: UE-ERROR
Short Syntax: LEC.020 nt network error_lvl log_point
Long Syntax: LEC.020 network network: lec error log: error_lvl log_point
Description: lec generic error
| LEC.021 |
Level: UE-ERROR
Short Syntax: LEC.021 nt network error_lvl log_point, D1= arg1
Long Syntax: LEC.021 network network: lec error log: error_lvl log_point, D1= arg1
Description: lec generic error with one arg
| LEC.022 |
Level: UE-ERROR
Short Syntax: LEC.022 nt network error_lvl log_point, D1= arg1, D2= arg2
Long Syntax: LEC.022 network network: lec error log: error_lvl log_point, D1= arg1, D2= arg2
Description: lec generic error with two args
| LEC.024 |
Level: UI-ERROR
Short Syntax: LEC.024 open frame SAP failed on nt n_net, rc= retcd
Long Syntax: LEC.024 open frame SAP failed on network n_net, rc = retcd
Description: open frame SAP failed
| LEC.025 |
Level: UI-ERROR
Short Syntax: LEC.025 open call SAP failed on nt n_net, rc= retcd
Long Syntax: LEC.025 open call SAP failed on network n_net, rc = retcd
Description: open call SAP failed
| LEC.026 |
Level: UI-ERROR
Short Syntax: LEC.026 open data path failed for outgoing call, on nt n_net, rc= retcd
Long Syntax: LEC.026 open data path failed for outgoing call, on network n_net, rc = retcd
Description: open data path failed for outgoing call
| LEC.027 |
Level: UI-ERROR
Short Syntax: LEC.027 open data path failed for incoming call, on nt n_net, rc= retcd
Long Syntax: LEC.027 open data path failed for incoming call, on network n_net, rc = retcd
Description: open data path failed for incoming call
| LEC.028 |
Level: C-INFO
Short Syntax: LEC.028 Function function_name called, nt network ID
Long Syntax: LEC.028 Function function_name called, on network network ID
Description: ATM LEC function called
| LEC.029 |
Level: UI-ERROR
Short Syntax: LEC.029 Start failed, on nt network ID, rc= retcd
Long Syntax: LEC.029 Start failed, on network network ID, rc = retcd
Description: Start failed for LEC object
| LEC.030 |
Level: UI-ERROR
Short Syntax: LEC.030 create LEC object failed, on nt network ID, rc= retcd
Long Syntax: LEC.030 create LEC object failed, on network network ID, rc = retcd
Description: Could not create LEC object
| LEC.031 |
Level: UI-ERROR
Short Syntax: LEC.031 usr reg failed, on nt network ID, rc= retcd
Long Syntax: LEC.031 user registration failed, on network network ID, rc = retcd
Description: LEC could not register
| LEC.032 |
Level: UI-ERROR
Short Syntax: LEC.032 nt network ID, ATM nt network ID nt nbld
Long Syntax: LEC.032 on network network ID, ATM network network ID not enabled
Description: ATM interface not enabled
| LEC.033 |
Level: UI-ERROR
Short Syntax: LEC.033 LEC activate failed, on nt network ID, rc= retcd
Long Syntax: LEC.033 LEC activate failed, on network network ID, rc = retcd
Description: LEC activate failed
| LEC.034 |
Level: UI-ERROR
Short Syntax: LEC.034 LEC activate complete, on nt network ID, rc= retcd
Long Syntax: LEC.034 LEC activate complete, on network network ID, rc = retcd
Description: LEC activate failed.
| LEC.035 |
Level: UI-ERROR
Short Syntax: LEC.035 Outbound frame freed, on nt network ID
Long Syntax: LEC.035 Outbound frame freed, on network network ID
Description: Outbound frame freed
| LEC.036 |
Level: UI-ERROR
Short Syntax: LEC.036 Outbound frame queued, on nt network ID
Long Syntax: LEC.036 Outbound frame queued, on network network ID
Description: Outbound frame queued
| LEC.037 |
Level: UI-ERROR
Short Syntax: LEC.037 Transmit failed, on nt network ID, rc= retcd
Long Syntax: LEC.037 Transmit failed, on network network ID, rc = retcd
Description: Transmit failed
| LEC.038 |
Level: UI-ERROR
Short Syntax: LEC.038 Outbound frame discarded, on nt network ID, rsn= reason,state= state,hndl= conn_handle
Long Syntax: LEC.038 Outbound frame discarded, on network network ID, reason = reason, DSM state = state, conn handle = conn_handle
Description: Outbound frame discarded
| LEC.039 |
Level: UI-ERROR
Short Syntax: LEC.039 LEC inbnd fr dscrd, size size, on nt network ID
Long Syntax: LEC.039 LEC inbound frame discarded, size size, on network network ID
Description: LEC inbound data frame was discarded - frame too small
| LEC.040 |
Level: UI-ERROR
Short Syntax: LEC.040 LEC inbnd fr dscrd, mcast addr, on nt network ID
Long Syntax: LEC.040 LEC inbnd fr dscrd, mcast address, on network network ID
Description: LEC inbound data frame was discarded - multicast data rcvd on data direct
| LEC.041 |
Level: UI-ERROR
Short Syntax: LEC.041 LEC inbnd fr dscrd, bad mac, on nt network ID
Long Syntax: LEC.041 LEC inbnd fr dscrd, bad mac address, on network network ID
Description: LEC inbound data frame was discarded - wrong MAC address
| LEC.042 |
Level: UI-ERROR
Short Syntax: LEC.042 SRAM nt fnd on dsbl, on nt network ID
Long Syntax: LEC.042 SRAM not found after disable, on network network ID
Description: Couldn't find the matching SRAM block after user disabled the LEC interface.
| LEC.043 |
Level: UI-ERROR
Short Syntax: LEC.043 cancel alarm, on nt net_no rc = rcode, num num
Long Syntax: LEC.043 Bad return from cancel alarm, on network net_no, rc = rcode, num = num
Description: Stopped timer and got bad return code.
| LEC.044 |
Level: C-TRACE
Short Syntax: LEC.044 nt network Rcvd Topology on conn handle conn_handle with xid xid
Long Syntax: LEC.044 network network Received Topology control frame on conn handle conn_handle with tran id of xid
Description: The LEC received a Topology control frame from the ATM network
| LEC.045 |
Level: C-TRACE
Short Syntax: LEC.045 nt network Sent Topology on conn handle conn_handle with xid xid
Long Syntax: LEC.045 network network Sent Topology control frame on conn handle conn_handle with tran id of xid
Description: The LEC sent a Topology control frame over the ATM network
| LEC.046 |
Level: UI-ERROR
Short Syntax: LEC.046 nt net_no LEC QoS object addresses unavailable
Long Syntax: LEC.046 nt net_no LEC QoS object addresses unavailable
Description: The LEC QoS object cannot obtain the object addresses of the LEC.
| LEC.047 |
Level: UI-ERROR
Short Syntax: LEC.047 nt net_no LEC QoS invld parms, entity:( maxReservedBW, trafficType, pcr, scr, qosClass, maxBurstSize),rc= rcode
Long Syntax: LEC.047 nt net_no LEC QoS invalid parms, entity(max= maxReservedBW kbps,type= trafficType,pcr= pcr kbps,scr= scr kbps,class= qosClass,busrt= maxBurstSize),rc= rcode
Description: LEC QoS invalid QoS parameters for an entity.
| LEC.048 |
Level: UI-ERROR
Short Syntax: LEC.048 nt net_no LEC QoS invld TLV rcvd, entity:type= tlvType
Long Syntax: LEC.048 nt net_no LEC QoS invalid TLV received, entity,type= tlvType
Description: LEC QoS invalid TLV received in a control frame (entity) with tlvType
| LEC.049 |
Level: UI-ERROR
Short Syntax: LEC.049 nt net_no LEC QoS error updating statisticts, invld type = statisticType
Long Syntax: LEC.049 nt net_no LEC QoS error updating statisticts, invld type = statisticType
Description: LEC QoS invalid type specified while updating statistics
| LEC.050 |
Level: UI-ERROR
Short Syntax: LEC.050 nt net_no LEC QoS error obtaining config parm configParm = value1
Long Syntax: LEC.050 nt net_no LEC QoS error obtaining configuration parameter configParm = value1
Description: LEC QoS error while obtaining configuration paramter from SRAM
| LEC.051 |
Level: U-INFO
Short Syntax: LEC.051 nt net_no lec tableId: incr tbl sz frm prevMaxConnEnties to newMaxConnEntries : statusString
Long Syntax: LEC.051 nt net_no lec tableId: increase table size from prevMaxConnEnties to newMaxConnEntries : Status statusString
Description: LEC component increasing the size of a table; operationh status is either SUCCESSFULL or FAILED
| LEC.052 |
Level: U-INFO
Short Syntax: LEC.052 nt net_no lec tableId: decr tbl sz frm prevMaxConnEnties to newMaxConnEntries : statusString
Long Syntax: LEC.052 nt net_no lec tableId: decrease table size from prevMaxConnEnties to newMaxConnEntries : Status statusString
Description: LEC component decreasing the size of a table; operationh status is either SUCCESSFULL or FAILED
| LEC.053 |
Level: UI-ERROR
Short Syntax: LEC.053 Outbnd frm dscrd, on nt net_no,frm sz ( frame_size) xcds cnfgd frm sz ( config_frame_size)
Long Syntax: LEC.053 Outbound frame discarded, on network net_no, frame size ( frame_size) exceeds configured frame size ( config_frame_size)
Description: An outbound frame was discarded, because the frame's size was larger than the configured frame size.
| LEC.054 |
Level: UI-ERROR
Short Syntax: LEC.054 Inbnd frm dscrd, on nt net_no,frm sz ( frame_size) xcds cnfgd frm sz ( config_frame_size)
Long Syntax: LEC.054 Inbound frame discarded, on network net_no, frame size ( frame_size) exceeds configured frame size ( config_frame_size)
Description: An inbound frame was discarded, because the frame's size was larger than the configured frame size.
| LEC.055 |
Level: C-INFO
Short Syntax: LEC.055 FLUSH msg prcssd by Redun IP Gtwy on nt net_no
Long Syntax: LEC.055 The LEC received a FLUSH msg that was processed by a Redundant IP Gateway on net net_no
Description: The LEC received a FLUSH message that was processed by the Redundant IP Gateway. These messages inform the backup gateways that the primary Gateway is attempting to activate.
| LEC.057 |
Level: DEBUG
Short Syntax: LEC.057 nt net_no:ntrng fn: function_name: parameters
Long Syntax: LEC.057 nt net_no:entering function: function_name: parameters
Description: The named function was entered
| LEC.058 |
Level: DEBUG
Short Syntax: LEC.058 nt net_no:xtng fn: function_name: parameters
Long Syntax: LEC.058 nt net_no:exiting function: function_name: parameters
Description: The named function was exited
| LEC.059 |
Level: UE-ERROR
Short Syntax: LEC.059 nt net_no:fn: function_name:ntry entry unknwn dest st dest_state
Long Syntax: LEC.059 nt net_no:function function_name:entry entry unknown destination state dest_state
Description: In the named function, the entry being processed is in an invalid state
| LEC.060 |
Level: CE-ERROR
Short Syntax: LEC.060 nt net_no:Mx LE_ARP rtry cnt ( retry_cnt) excd fr arp_entry
Long Syntax: LEC.060 nt net_no:Max LE_ARP retry count ( retry_cnt) exceeded from arp_entry
Description: Max ARP entry count exceeded. Any queued frames will be discarded and the ARP entry will be deleted
| LEC.061 |
Level: C-INFO
Short Syntax: LEC.061 nt net_no:ARP cycl tmr xprd:ntry arp_entry st state
Long Syntax: LEC.061 nt net_no:ARP cycle timer expired:entry arp_entry state state
Description: The ARP cycle timer has expired for the specified entry. The ARP entry will be released.
| LEC.062 |
Level: C-INFO
Short Syntax: LEC.062 nt net_no:Flsh tmr xprd:ntry arp_entry st state
Long Syntax: LEC.062 nt net_no:Flush timer expired:entry arp_entry state state
Description: The Flush timer has expired for the specified entry. If the specified state is FLUSHING, any queued frames will be discarded, and another Flush request will be sent.
| LEC.063 |
Level: UI-ERROR
Short Syntax: LEC.063 nt net_no:Orphnd Flsh tmr xprd:ntry arp_entry st state
Long Syntax: LEC.063 nt net_no:Orphaned Flush timer expired:entry arp_entry state state
Description: An orphaned Flush timer has expired for the specified entry. In the specified state, a flush timer should not be active.
| LEC.064 |
Level: C-INFO
Short Syntax: LEC.064 nt net_no:PSD tmr xprd:ntry arp_entry st state
Long Syntax: LEC.064 nt net_no:PSD timer expired:entry arp_entry state state
Description: The Path Switch Delay timer has expired for the specified entry. If the specified state is FLUSHING, any queued frames will be forwarded.
| LEC.065 |
Level: UI-ERROR
Short Syntax: LEC.065 nt net_no:Orphnd PSD tmr xprd:ntry arp_entry st state
Long Syntax: LEC.065 nt net_no:Orphaned PSD timer expired:entry arp_entry state state
Description: An orphaned PSD timer has expired for the specified entry. In the specified state, a PSD timer should not be active.
| LEC.066 |
Level: C-INFO
Short Syntax: LEC.066 nt net_no:Rdy rtry cnt eqls mx rdy rtries ( max_rdy_retries), ntry art_entry
Long Syntax: LEC.066 nt net_no:Ready retry count equals max ready retries( max_rdy_retries), entry art_entry
Description: The ready retry count equals the defined max ready retries, and the entry's state is CALL PENDING. The call will be hung up.
| LEC.067 |
Level: UI-ERROR
Short Syntax: LEC.067 nt net_no:xmt ctrl frm, rdy qry fld,ntry art_entry
Long Syntax: LEC.067 nt net_no:xmit control frame, ready query failed, entry art_entry
Description: An error occured while transmitting a ready query.
| LEC.068 |
Level: UI-ERROR
Short Syntax: LEC.068 nt net_no:Orphnd Rdy tmr xprd:ntry art_entry st state
Long Syntax: LEC.068 nt net_no:Orphaned Ready timer expired:entry art_entry state state
Description: An orphaned Ready timer has expired for the specified entry. In the specified state, a Ready timer should not be active.
| LEC.069 |
Level: UI-ERROR
Short Syntax: LEC.069 nt net_no:Plc cll fld:out of rsrc, addr atm_addr
Long Syntax: LEC.069 nt net_no:Place call failed:out of resource, address atm_addr
Description: Place call for outbound data direct connection failed, due to a lack of resources.
| LEC.070 |
Level: UI-ERROR
Short Syntax: LEC.070 nt net_no:fn function_name:ntry entry unknwn cll st call_state
Long Syntax: LEC.070 nt net_no:function function_name:entry entry unknown call state call_state
Description: In the named function, the entry being processed is in an invalid state
| LEC.071 |
Level: UE-ERROR
Short Syntax: LEC.071 nt net_no:Mltpl cnnctns exst to cllr addr caller_addr
Long Syntax: LEC.071 nt net_no:Multiple connections exist to caller address caller_addr
Description: An inbound data direct call was received. The call will be rejected because multiple connections exist to the calling party.
| LEC.072 |
Level: UI-ERROR
Short Syntax: LEC.072 nt net_no:Rcv cll fld:out of rsrc, conn hndl conn_handle
Long Syntax: LEC.072 nt net_no:Receive call failed:out of resource,conn handle conn_handle
Description: Receive call for inbound data direct connection failed, due to a lack of resources.
| LEC.073 |
Level: C-INFO
Short Syntax: LEC.073 nt net_no:Rdy Indct rcvd,ntry art_entry st state
Long Syntax: LEC.073 nt net_no:Ready Indicate received,entry art_entry state state
Description: Ready Indicate frame has been received
| LEC.074 |
Level: UE-ERROR
Short Syntax: LEC.074 nt net_no:Rdy Indct rcvd,cll st err ,ntry art_entry st state
Long Syntax: LEC.074 nt net_no:Ready Indicate received,call state error, entry art_entry state state
Description: A Ready Indicate frame should not be received on a connection in this state.
| LEC.075 |
Level: UI-ERROR
Short Syntax: LEC.075 nt net_no:Rdy Indct rcvd,unknwn conn, conn hndl conn_handle
Long Syntax: LEC.075 nt net_no:Ready Indicate received,unknown connection, conn handle conn_handle
Description: A Ready Indicate frame was received on a connection that is unknown by the LEC.
| LEC.076 |
Level: C-INFO
Short Syntax: LEC.076 nt net_no:Plc Cll Ack rcvd,ntry art_entry st state
Long Syntax: LEC.076 nt net_no:Place Call Ack Received,entry art_entry state state
Description: A Place Call Ack has been received
| LEC.077 |
Level: UI-ERROR
Short Syntax: LEC.077 nt net_no:xmt ctrl frm,rdy indct fld,addr atm_addr
Long Syntax: LEC.077 nt net_no:xmit control frame,ready indicate failed, address atm_addr
Description: Unable to send the ready indicate control frame
| LEC.078 |
Level: UE-ERROR
Short Syntax: LEC.078 nt net_no:Plc Cll Ack rcvd,cll st err ,ntry art_entry st state
Long Syntax: LEC.078 nt net_no:Place Call Ack received,call state error, entry art_entry state state
Description: A Place Call Ack should not be received on a connection in this state.
| LEC.079 |
Level: UI-ERROR
Short Syntax: LEC.079 nt net_no:Plc Cll Ack rcvd,unknwn conn, conn hndl conn_handle
Long Syntax: LEC.079 nt net_no:Place Call Ack received,unknown connection, conn handle conn_handle
Description: A Place Call Ack was received on a connection that is unknown by the LEC.
| LEC.080 |
Level: C-INFO
Short Syntax: LEC.080 nt net_no:Rtrng cll estblshmnt, ntry art_entry
Long Syntax: LEC.080 nt net_no:Retrying call establishment, entry art_entry
Description: Call is being disconnected, attempt to re-establish connection
| LEC.081 |
Level: UI-ERROR
Short Syntax: LEC.081 nt net_no:Dscnnct rcvd,unknwn conn, conn hndl conn_handle
Long Syntax: LEC.081 nt net_no:Disconnect received,unknown connection, conn handle conn_handle
Description: A disconnect was received for a connection that is unknown by the LEC.
| LEC.082 |
Level: C-INFO
Short Syntax: LEC.082 nt net_no:HngUp cll rcvd,ntry art_entry st state
Long Syntax: LEC.082 nt net_no:HangUp call received,entry art_entry state state
Description: HangUp call has been received
| LEC.083 |
Level: UI-ERROR
Short Syntax: LEC.083 nt net_no:HngUp cll rcvd,unknwn conn, conn hndl conn_handle
Long Syntax: LEC.083 nt net_no:HangUp call received,unknown connection, conn handle conn_handle
Description: A HangUp Call was received for a connection that is unknown by the LEC.
| LEC.084 |
Level: UI-ERROR
Short Syntax: LEC.084 nt net_no:fn function_name:unknwn clnt st client_state
Long Syntax: LEC.084 nt net_no:function function_name:unknown client state client_state
Description: In the named function, the LEC is in an invalid state
| LEC.085 |
Level: UE-ERROR
Short Syntax: LEC.085 nt net_no:Plc Cll Ack for Cfg Drct rcvd,clnt st err ,st state
Long Syntax: LEC.085 nt net_no:Place Call Ack for Cfg Direct received,client state error, state state
Description: A Place Call Ack for a Config Direct VCC should not be received for a LEC in this state.
| LEC.086 |
Level: UI-ERROR
Short Syntax: LEC.086 nt net_no:Unbl to strt jn rqst tmr
Long Syntax: LEC.086 nt net_no:Unable to start join request timer
Description: The join request timer could not be started for this LEC.
| LEC.087 |
Level: UI-ERROR
Short Syntax: LEC.087 nt net_no:xmt ctrl frm,jn rqst fld
Long Syntax: LEC.087 nt net_no:xmit control frame,join request failed
Description: Unable to send the join request control frame
| LEC.088 |
Level: UE-ERROR
Short Syntax: LEC.088 nt net_no:Plc Cll Ack for Ctrl Drct rcvd,clnt st err ,st state
Long Syntax: LEC.088 nt net_no:Place Call Ack for Control Direct received,client state error, state state
Description: A Place Call Ack for a Control Direct VCC should not be received for a LEC in this state.
| LEC.089 |
Level: UE-ERROR
Short Syntax: LEC.089 nt net_no:Plc Cll Ack for Mcst Snd rcvd,clnt st err ,st state
Long Syntax: LEC.089 nt net_no:Place Call Ack for Mcast Send received,client state error, state state
Description: A Place Call Ack for a Multicast Send VCC should not be received for a LEC in this state.
| LEC.090 |
Level: UI-ERROR
Short Syntax: LEC.090 nt net_no:PVC stup to LECS fld
Long Syntax: LEC.090 nt net_no:PVC setup to LECS failed
Description: Attempt to set up PVC for LECS (VPI 0,VCI 17) failed
| LEC.091 |
Level: UE-ERROR
Short Syntax: LEC.091 nt net_no:Dscnnct for Cnfg Drct rcvd,clnt st err ,st state
Long Syntax: LEC.091 nt net_no:Disconnect for Config Direct received,client state error, state state
Description: A disconnect for a Config Direct VCC should not be received for a LEC in this state.
| LEC.092 |
Level: UE-ERROR
Short Syntax: LEC.092 nt net_no:Dscnnct for Ctrl Drct rcvd,clnt st err ,st state
Long Syntax: LEC.092 nt net_no:Disconnect for Control Direct received,client state error, state state
Description: A disconnect for a Control Direct VCC should not be received for a LEC in this state.
| LEC.093 |
Level: UE-ERROR
Short Syntax: LEC.093 nt net_no:Dscnnct for Ctrl Dstrbt rcvd,clnt st err ,st state
Long Syntax: LEC.093 nt net_no:Disconnect for Control Distribute received,client state error, state state
Description: A disconnect for a Control Distribute VCC should not be received for a LEC in this state.
| LEC.094 |
Level: C-INFO
Short Syntax: LEC.094 nt net_no:Rtryng Mcst Snd conn to BUS
Long Syntax: LEC.094 nt net_no:Retrying Mcst Send connection to BUS
Description: Try to set up Multicast Send connection to BUS.
| LEC.095 |
Level: UE-ERROR
Short Syntax: LEC.095 nt net_no:Dscnnct for Mcst Snd rcvd,clnt st err ,st state
Long Syntax: LEC.095 nt net_no:Disconnect for Mcast Send received,client state error, state state
Description: A disconnect for a Multicst Send VCC should not be received for a LEC in this state.
| LEC.096 |
Level: UE-ERROR
Short Syntax: LEC.096 nt net_no:Dscnnct for Mcst Fwd rcvd,clnt st err ,st state
Long Syntax: LEC.096 nt net_no:Disconnect for Mcast Fwd received,client state error, state state
Description: A disconnect for a Multicst Forward VCC should not be received for a LEC in this state.
| LEC.097 |
Level: UE-ERROR
Short Syntax: LEC.097 nt net_no:Cnfg Rsp err, trans id (x trans_id) not eql rsp trans id (x rsp_trans_id)
Long Syntax: LEC.097 nt net_no:Config Rsp error,trans id (x trans_id) not equal response trans id (x rsp_trans_id)
Description: The transaction id in the config request and config response, was not equal. The transaction id should be the same in the request and response.
| LEC.098 |
Level: UE-ERROR
Short Syntax: LEC.098 nt net_no:Cnfg Rsp err, st status
Long Syntax: LEC.098 nt net_no:Config Rsp error, status status
Description: The config response returned the stated error status.
| LEC.099 |
Level: UE-ERROR
Short Syntax: LEC.099 nt net_no:Vldtn of cnfg parms frm LECS fld
Long Syntax: LEC.099 nt net_no:Validation of config parms from LECS failed
Description: The validation of the LEC's config parms from the LECS failed.
| LEC.101 |
Level: UE-ERROR
Short Syntax: LEC.101 nt net_no:Jn Rsp err, st status
Long Syntax: LEC.101 nt net_no:Jn Rsp error, status status
Description: The join response returned the stated error status.
| LEC.102 |
Level: UI-ERROR
Short Syntax: LEC.102 nt net_no:xmt ctrl frm,arp rqst fld, dst dest_mac
Long Syntax: LEC.102 nt net_no:xmit control frame,arp request failed, dest dest_mac
Description: Unable to send the arp request control frame
| LEC.103 |
Level: UI-ERROR
Short Syntax: LEC.103 nt net_no:Unbl to strt arp rqst tmr
Long Syntax: LEC.103 nt net_no:Unable to start arp request timer
Description: The arp request timer could not be started for this LEC.
| LEC.104 |
Level: UE-ERROR
Short Syntax: LEC.104 nt net_no:Jn rsp rcvd,clnt st err ,st state
Long Syntax: LEC.104 nt net_no:Join response received,client state error, state state
Description: A Join response should not be received by a LEC in this state.
| LEC.105 |
Level: UI-ERROR
Short Syntax: LEC.105 nt net_no:Flsh rsp rcvd,no ARP ntry ,st state
Long Syntax: LEC.105 nt net_no:Flush response received,no ARP entry, state state
Description: A Flush response was received, but an associated ARP entry was not found.
| LEC.106 |
Level: UE-ERROR
Short Syntax: LEC.106 nt net_no:Flsh rsp rcvd,src addr src_addr, LEC addr lec_addr msmtch
Long Syntax: LEC.106 nt net_no:Flush response received,source addr src_addr, LEC addr lec_addr mismatch
Description: A Flush response was received, but the frame's source address does not match the LEC's address.
| LEC.107 |
Level: UE-ERROR
Short Syntax: LEC.107 nt net_no:LE ARP Rsp err, st status, dst dest_mac
Long Syntax: LEC.107 nt net_no:LE ARP Rsp error, status status, dest dest_mac
Description: The LE ARP response returned the stated error status.
| LEC.108 |
Level: UE-ERROR
Short Syntax: LEC.108 nt net_no:Invld tag( tag), LE ARP Rsp, st state
Long Syntax: LEC.108 nt net_no:Invalid tag ( tag) LE ARP Rsp, state state
Description: The LE ARP response contains an invalid tag.
| LEC.109 |
Level: UI-ERROR
Short Syntax: LEC.109 nt net_no:LE ARP Rsp rcvd,no ARP ntry, dest dest_mac st state
Long Syntax: LEC.109 nt net_no:LE ARP Rsp received,no ARP entry, dest dest_mac state state
Description: A LE ARP response was received, but an associated ARP entry was not found.
| LEC.110 |
Level: UE-ERROR
Short Syntax: LEC.110 nt net_no:Invld tag( tag), LE NARP Rqst, st state
Long Syntax: LEC.110 nt net_no:Invalid tag ( tag) LE ARP Rqst, state state
Description: The LE NARP request contains an invalid tag.
| LEC.111 |
Level: UI-ERROR
Short Syntax: LEC.111 nt net_no:Jn timeout exceeded
Long Syntax: LEC.111 nt net_no:Join timeout exceeded
Description: The join timeout was exceeded.
| LEC.112 |
Level: UI-ERROR
Short Syntax: LEC.112 nt net_no:Cnfg rqst tmout ( config_timeout) excds cntrl tmout( control_timeout)
Long Syntax: LEC.112 nt net_no:Config request timeout ( config_timeout) exceeds control timeout ( control_timeout)
Description: The config request timeout exceeds the control timeout.
| LEC.113 |
Level: UI-ERROR
Short Syntax: LEC.113 nt net_no:Cnfg Req tmr xprd,clnt st err ,st state
Long Syntax: LEC.113 nt net_no:Config Request timer expired,client state error, state state
Description: The Config Request timer should not expire for a LEC in this state.
| LEC.114 |
Level: UI-ERROR
Short Syntax: LEC.114 nt net_no:LE ARP rtry cnt ( arp_retry_cnt) fr BUS eqls mx rtries
Long Syntax: LEC.114 nt net_no:LE ARP retry count ( arp_retry_cnt) for BUS equals max retries
Description: The LE ARP retry count equals the max retry count.
| LEC.115 |
Level: UI-ERROR
Short Syntax: LEC.115 nt net_no:LE ARP fr BUS tmr xprd,clnt st err ,st state
Long Syntax: LEC.115 nt net_no:LE ARP for BUS timer expired,client state error, state state
Description: The LE ARP Request timer should not expire for a LEC in this state.
| LEC.116 |
Level: UE-ERROR
Short Syntax: LEC.116 nt net_no:Cnfg Rsp cntrl frm err,src ( src_dest) not LEC's ( lec_mac)
Long Syntax: LEC.116 nt net_no:Config Response control frame error, source ( src_dest) not LEC's ( lec_mac)
Description: A config response control frame was received. The source MAC address does not equal the LEC's MAC address.
| LEC.117 |
Level: UE-ERROR
Short Syntax: LEC.117 nt net_no:Cnfg Rsp cntrl frm err, invld eln nm sz ( name_size)
Long Syntax: LEC.117 nt net_no:Config Response control frame error,invalid ELAN name size ( name_size)
Description: A config response control frame was received. The ELAN name size is invalid.
| LEC.118 |
Level: UE-ERROR
Short Syntax: LEC.118 nt net_no:Cnfg Rsp cntrl frm err, invld frm sz ( frame_size)
Long Syntax: LEC.118 nt net_no:Config Response control frame error,invalid frame size ( frame_size)
Description: A config response control frame was received. The maximum frame size is invalid.
| LEC.119 |
Level: UE-ERROR
Short Syntax: LEC.119 nt net_no:Cnfg Rsp cntrl frm err, invld prmtr config_parm
Long Syntax: LEC.119 nt net_no:Config Response control frame error,invalid parameter config_parm
Description: A config response control frame was received. The specified config parm is invalid, or out of range.
| LEC.120 |
Level: UE-ERROR
Short Syntax: LEC.120 nt net_no:Jn Rsp cntrl frm err, invld frm sz ( frame_size)
Long Syntax: LEC.120 nt net_no:Join Response control frame error,invalid frame size ( frame_size)
Description: A join response control frame was received. The maximum frame size is invalid.
| LEC.121 |
Level: UE-ERROR
Short Syntax: LEC.121 nt net_no:Jn Rsp cntrl frm err, lan typ ( lan_type) not eql to LEC ( lec_lan_type)
Long Syntax: LEC.121 nt net_no:Join Response control frame error,lan type ( lan_type) not equal to LEC ( lec_lan_type)
Description: A join response control frame was received. The lan type in the response does not match the LEC's lan type .
| LEC.122 |
Level: UI-ERROR
Short Syntax: LEC.122 nt net_no:Unbl to strt cnfg rqst tmr
Long Syntax: LEC.122 nt net_no:Unable to start cnfg request timer
Description: The config request timer could not be started for this LEC.
| LEC.123 |
Level: UI-ERROR
Short Syntax: LEC.123 nt net_no:xmt cntrl frm,cnfg rqst fld
Long Syntax: LEC.123 nt net_no:xmit control frame,cnfg request failed
Description: Unable to send the config request control frame
| LEC.124 |
Level: UI-ERROR
Short Syntax: LEC.124 nt net_no:Jn Req tmr xprd,clnt st err ,st state
Long Syntax: LEC.124 nt net_no:Join Request timer expired,client state error, state state
Description: The Join Request timer should not expire for a LEC in this state.
| LEC.125 |
Level: UI-ERROR
Short Syntax: LEC.125 nt net_no:set alrm tmr rtrn null pntr, fn function_name, alrm type alarm_type
Long Syntax: LEC.125 nt net_no:Set Alarm timer returned a null pointer, function function_name, alarm type alarm_type
Description: Unable to allocate an alarm timer.
| LEC.126 |
Level: C-INFO
Short Syntax: LEC.126 nt net_no:Regstrd lan dest/RD lan_dest w/LES
Long Syntax: LEC.126 nt net_no:Registered lan destination/Route Descriptor lan_dest with LES
Description: LEC registered a lan destination or route descriptor with the LES.
| LEC.127 |
Level: UI-ERROR
Short Syntax: LEC.127 nt net_no:Fld to reg lan dest/RD lan_dest w/LES
Long Syntax: LEC.127 nt net_no:Failed to register lan destination/Route Descriptor lan_dest with LES
Description: Attempt to register a lan destination or route descriptor with the LES failed.
| LEC.128 |
Level: UI-ERROR
Short Syntax: LEC.128 nt net_no:fn function_name:unknwn RSM st rsm_state
Long Syntax: LEC.128 nt net_no:function function_name:unknown RSM state rsm_state
Description: In the named function, the LEC RSM is in an invalid state.
| LEC.129 |
Level: UI-ERROR
Short Syntax: LEC.129 nt net_no:Fld to reg lan dest/RD dest_addr (atm addr dest_atm_addr) w/LES
Long Syntax: LEC.129 nt net_no:Failed to register lan destination/Route Descriptor dest_addr (atm address dest_atm_addr) with LES
Description: Attempt to register a lan destination or route descriptor with the LES failed.
| LEC.130 |
Level: UI-ERROR
Short Syntax: LEC.130 nt net_no:fn function_name:lec fld to get reg req timr
Long Syntax: LEC.130 nt net_no:function function_name:lec failed to get register request timer
Description: In the named function, the LEC failed to get a register request timer.
| LEC.131 |
Level: UI-ERROR
Short Syntax: LEC.131 nt net_no:fn function_name:lec reg xmit join req fld
Long Syntax: LEC.131 nt net_no:function function_name:lec register transmit join request failed
Description: In the named function, the LEC failed to transmit join request.
| LEC.132 |
Level: UI-ERROR
Short Syntax: LEC.132 nt net_no:fn function_name: unxpctd rsp rcvd, st rsm_state, rsp rsp_OpCode
Long Syntax: LEC.132 nt net_no:function function_name:unexpected response received, state rsm_state, response rsp_OpCode
Description: In the named function, an unexpected response received for given RSM state.
| LEC.133 |
Level: U-INFO
Short Syntax: LEC.133 nt net_no:LEC nt oprtnl, st state
Long Syntax: LEC.133 nt net_no:LEC not operational, state state
Description: The LEC is not operational.
| LEC.134 |
Level: UI-ERROR
Short Syntax: LEC.134 nt net_no:Outbnd frm dscrd, dst = dest_addr src = src_addr, rsn = reason
Long Syntax: LEC.134 nt net_no:Outbound frame discarded, dest = dest_addr source = src_addr, reason = reason
Description: Outbound frame discarded
| LEC.135 |
Level: DEBUG
Short Syntax: LEC.135 nt net_no:Snd frm on Mcast Snd VCC, dst = dest_addr src = src_addr
Long Syntax: LEC.135 nt net_no:Send frame on Multicast Send VCC, dest = dest_addr source = src_addr
Description: A frame was sent on the Multicast Send VCC.
| LEC.136 |
Level: U-INFO
Short Syntax: LEC.136 nt net_no:No cnnctn to BUS
Long Syntax: LEC.136 nt net_no:No connection to BUS
Description: The LEC does not have a connection to the BUS.
| LEC.137 |
Level: UI-ERROR
Short Syntax: LEC.137 nt net_no:No ARP entrs avlbl,hngup lst usd conn fld
Long Syntax: LEC.137 nt net_no:No ARP entires available, hangup least used connection failed
Description: The LEC's ARP table is full.
| LEC.138 |
Level: DEBUG
Short Syntax: LEC.138 nt net_no:Snd Drctd frm, dst = dest_addr src = src_addr
Long Syntax: LEC.138 nt net_no:Send Directed frame, dest = dest_addr source = src_addr
Description: Directed frame was sent.
| LEC.139 |
Level: UI-ERROR
Short Syntax: LEC.139 nt net_no:Inbnd frm dscrd, dst = dest_addr src = src_addr, rsn = reason
Long Syntax: LEC.139 nt net_no:Inbound frame discarded, dest = dest_addr source = src_addr, reason = reason
Description: Inbound frame discarded
| LEC.140 |
Level: DEBUG
Short Syntax: LEC.140 nt net_no:Rcvd frame_type cntrl frm,trans id x trans_id, conn hndl conn_handle
Long Syntax: LEC.140 nt net_no:Received frame_type control frame, trans id x trans_id, connection handle conn_handle
Description: The specified control frame was received by the LEC.
| LEC.141 |
Level: U-INFO
Short Syntax: LEC.141 nt net_no:Dscrd LE_ARP Rqst. str_port prt nt in fwding st. Prt st str_state(0x port_state)
Long Syntax: LEC.141 nt net_no:Discarded LE_ARP Request. str_port port not in forwarding state. Port state is str_state(0x port_state)
Description: The LEC should not respond to a LE_ARP Request if the local or remote port is not in the forwarding state.
| LEC.142 |
Level: UI_ERROR
Short Syntax: LEC.142 nt net_no:Get LEC's cnfg prms fld
Long Syntax: LEC.142 nt net_no:Get LEC's config parameters failed
Description: Reading the LEC's configuration parameters failed.
| LEC.143 |
Level: UI_ERROR
Short Syntax: LEC.143 nt net_no:Create objct LEC_object fld
Long Syntax: LEC.143 nt net_no:Create object LEC_object failed
Description: The specified LEC object could not be created.
| LEC.144 |
Level: UI_ERROR
Short Syntax: LEC.144 nt net_no:Rgstr dest dest_addr fld, rsn reason
Long Syntax: LEC.144 nt net_no:Register destination dest_addr failed, rsn reason
Description: The specified destination could not be registered with the LES.
| LEC.145 |
Level: UI_ERROR
Short Syntax: LEC.145 nt net_no:ATM addr actvtd, invld st client_state
Long Syntax: LEC.145 nt net_no:ATM address activated, invalid state client_state
Description: The ATM addr should not be activated while the LEC is in this state.
| LEC.146 |
Level: UI_ERROR
Short Syntax: LEC.146 nt net_no:ATM addr actvtd, ILMI fld
Long Syntax: LEC.146 nt net_no:ATM address activated, ILMI failure
Description: An ILMI failure occurred.
| LEC.147 |
Level: UE_ERROR
Short Syntax: LEC.147 nt net_no:Get LECS addr fld
Long Syntax: LEC.147 nt net_no:Get LECS address failed
Description: The LEC was unable to get the LECS address.
| LEC.148 |
Level: UE_ERROR
Short Syntax: LEC.148 nt net_no:Cntrl Drct setup fld
Long Syntax: LEC.148 nt net_no:Control Direct setup failed
Description: The LEC was unable to set up the Control Direct VCC to the LES.
| LEC.149 |
Level: UE_ERROR
Short Syntax: LEC.149 nt net_no:Cnfg Drct setup fld
Long Syntax: LEC.149 nt net_no:Config Direct setup failed
Description: The LEC was unable to set up the Config Direct VCC to the LECS.
| LEC.150 |
Level: U_INFO
Short Syntax: LEC.150 nt net_no:Unslctd Cnfg Rsp rcvd
Long Syntax: LEC.150 nt net_no:Unsolicited Config Response received
Description: The LEC received an unsolicited Config Response frame.
| LEC.151 |
Level: DEBUG
Short Syntax: LEC.151 nt net_no:xmt ctrl frm frame_type ,trans id x trans_id, conn hndl conn_handle
Long Syntax: LEC.151 nt net_no:xmit control frame frame_type, trans id x trans_id, connection handle conn_handle
Description: The specified control frame was transmitted.
| LEC.152 |
Level: UE-ERROR
Short Syntax: LEC.152 nt net_no:Invld LE ARP Rsp,rsn status
Long Syntax: LEC.152 nt net_no:Invalid LE ARP Response, reason status
Description: The LE ARP response is invalid for the stated reason.
| LEC.153 |
Level: UE-ERROR
Short Syntax: LEC.153 nt net_no:Place call ack for unknwn conn, st client_state
Long Syntax: LEC.153 nt net_no:Place call ack for unknown connection, state client_state
Description: A place call ack was received for an unknown connection.
| LEC.154 |
Level: UE-ERROR
Short Syntax: LEC.154 nt net_no:lec_cmgr has conn_tbl/freelist inconsistency, index = index
Long Syntax: LEC.154 nt net_no:lec_mgr has conn_tbl/freelist inconsisency, index = index
Description: An inconsistency has been found when acquiring an new conn blk.
| LEC.155 |
Level: UE-ERROR
Short Syntax: LEC.155 nt net_no:lec_cmgr:decrTblSz err: tblSz= max_conn_handles, connEntries= non_null_entries, flstAvl= freelist_available
Long Syntax: LEC.155 nt net_no:lec_cmgr:decrTblSz error: tblSz= max_conn_handles, connEntries= non_null_entries, flstAvl= freelist_available
Description: An inconsistency has been found when decreasing a LEC connection table.
| LEC.156 |
Level: U-INFO
Short Syntax: LEC.156 nt net_no:lec_cmgr:decrTblSz check OK: tblSz= max_conn_handles, flstAvl= freelist_available
Long Syntax: LEC.156 nt net_no:lec_cmgr:decrTblSz check OK: tblSz= max_conn_handles, flstAvl= freelist_available
Description: Consistency check OK in lec_cmgr:decrease_conn_tbl but table not decreased.
| LEC.157 |
Level: UI-ERROR
Short Syntax: LEC.157 nt net_no:Unbl to allct ART entry
Long Syntax: LEC.157 nt net_no:Unable to allocate ART entry
Description: An ART entry could not be allocated.
| LEC.158 |
Level: DEBUG
Short Syntax: LEC.158 nt net_no:Snt frm to BUS on conn hndl conn_handle, frm cnt frame_cnt
Long Syntax: LEC.158 nt net_no:Sent frame to BUS on conn handle conn_handle, frame count frame_cnt
Description: The LEC sent a frame to the BUS, because a data direct does not yet exist to the destination.
| LEC.159 |
Level: UE-ERROR
Short Syntax: LEC.159 nt net_no:ARP Rsp err, trans id (x trans_id) not eql rsp trans id (x rsp_trans_id)
Long Syntax: LEC.159 nt net_no:ARP Rsp error,trans id (x trans_id) not equal response trans id (x rsp_trans_id)
Description: The transaction id in the ARP request and ARP response, was not equal. The transaction id should be the same in the request and response.
| LEC.160 |
Level: C-INFO
Short Syntax: LEC.160 nt net_no:LEC rcvd mltpl ARP rsp
Long Syntax: LEC.160 nt net_no:LEC received multiple ARP responses
Description: The LEC received multiple ARP responses to an ARP request.
| LEC.161 |
Level: UE-ERROR
Short Syntax: LEC.161 nt net_no:fn: function_name:ntry entry invld dest st dest_state
Long Syntax: LEC.161 nt net_no:function function_name:entry entry invalid destination state dest_state
Description: In the named function, the entry being processed is in an invalid state
| LEC.162 |
Level: UI-ERROR
Short Syntax: LEC.162 nt net_no:Dscrd frame_cnt queued frms, st dest_state, conn hndl conn_hndl
Long Syntax: LEC.162 nt net_no:Discarded frame_cnt queued frames, state dest_state, conn handle conn_hndl
Description: The LEC has discarded the stated number of queued frames
| LEC.163 |
Level: UI-ERROR
Short Syntax: LEC.163 nt net_no:Purge queued frms fld
Long Syntax: LEC.163 nt net_no:Purge queued frames failed
Description: An error occurred while the LEC was attempting to free the queued frames
| LEC.164 |
Level: UI-ERROR
Short Syntax: LEC.164 nt net_no:Err purging queued frms, queue not empty
Long Syntax: LEC.164 nt net_no:Error purging queued frames, queue not empty
Description: All frames should have been removed from the queue.
| LEC.165 |
Level: UI-ERROR
Short Syntax: LEC.165 nt net_no:Snd queued frms fld,queue empty
Long Syntax: LEC.165 nt net_no:Send queued frames failed, queue empty
Description: An error occurred while the LEC was attempting to send the queued frames
| LEC.166 |
Level: UI-ERROR
Short Syntax: LEC.166 nt net_no:Err snding queued frms, queue not empty
Long Syntax: LEC.166 nt net_no:Error sending queued frames, queue not empty
Description: All frames should have been sent.
| LEC.167 |
Level: UI-ERROR
Short Syntax: LEC.167 nt net_no:xmt ctrl frm,flsh rqst fld, dst dest_mac
Long Syntax: LEC.167 nt net_no:xmit control frame,flush request failed, dest dest_mac
Description: Unable to send the flush request control frame
| LEC.168 |
Level: DEBUG
Short Syntax: LEC.168 nt net_no:srch tbl table, addr address
Long Syntax: LEC.168 nt net_no:search tbl table, address address
Description: The specified table was searched for the address.
| LEC.169 |
Level: UI-ERROR
Short Syntax: LEC.169 nt net_no:Unbl to add database_type dtbs entry, entry
Long Syntax: LEC.169 nt net_no:Unable to add database_type database entry, entry
Description: An entry could not be added to the specified database.
| LEC.170 |
Level: UI-ERROR
Short Syntax: LEC.170 nt net_no:ARP tbl full, No ARP entrs avlbl
Long Syntax: LEC.170 nt net_no:ARP table full, No ARP entries available
Description: The LEC's ARP table is full.
| LEC.171 |
Level: UI-ERROR
Short Syntax: LEC.171 nt net_no:No entrs in tbl
Long Syntax: LEC.171 nt net_no:No entries in table
Description: The LEC's ARP table is empty.
| LEC.172 |
Level: UI-ERROR
Short Syntax: LEC.172 nt net_no:Invld tag( tag), rls arp entry
Long Syntax: LEC.172 nt net_no:Invalid tag ( tag),release arp entry
Description: Attempting to release an ARP entry which has an invalid tag.
| LEC.173 |
Level: UI-ERROR
Short Syntax: LEC.173 nt net_no:ntry arp_entry, xmit queue nt empty ( xmit_queue_count), rls arp entry
Long Syntax: LEC.173 nt net_no:Entry arp_entry, xmit queue not empty ( xmit_queue_count),release arp entry
Description: Attempting to release an ARP entry which has a non-empty transmit queue.
| LEC.174 |
Level: UI-ERROR
Short Syntax: LEC.174 nt net_no:fn function, unbl to allct memry
Long Syntax: LEC.174 nt net_no:Function function, unable to allocate memory
Description: The specified function was unable to allocate memory.
| LEC.175 |
Level: UI-ERROR
Short Syntax: LEC.175 nt net_no:Invld LEC or ART ptr
Long Syntax: LEC.175 nt net_no:Invalid LEC or ART pointer
Description: The LEC or ART pointer is invalid.
| LEC.176 |
Level: UE-ERROR
Short Syntax: LEC.176 nt net_no:Invld AAL parms( AAL_parms), cll rjctd
Long Syntax: LEC.176 nt net_no:Invalid AAL parms( AAL_parms), call rejected
Description: Call will be rejected due to invalid AAL parameters.
| LEC.177 |
Level: U-INFO
Short Syntax: LEC.177 nt net_no:Invld PID in rcv cll
Long Syntax: LEC.177 nt net_no:Invalid PID in receive call
Description: Call was received with an invalid PID.
| LEC.178 |
Level: UI-ERROR
Short Syntax: LEC.178 nt net_no:place call fld, rsn reason
Long Syntax: LEC.178 nt net_no:place call failed, reason reason
Description: Place call failed for the following reason.
| LEC.179 |
Level: UI-ERROR
Short Syntax: LEC.179 nt net_no:get ART cnfg parms fld
Long Syntax: LEC.179 nt net_no:get ART config parms failed
Description: Unable to get ART config parameters.
| LEC.180 |
Level: UI-ERROR
Short Syntax: LEC.180 nt net_no:ART tbl full, No ART entrs avlbl
Long Syntax: LEC.180 nt net_no:ART table full, No ART entries available
Description: The LEC's ART table is full.
| LEC.181 |
Level: UI-ERROR
Short Syntax: LEC.181 nt net_no:ART entry alrdy freed
Long Syntax: LEC.181 nt net_no:ART entry already freed
Description: The ART has already been freed.
| LEC.182 |
Level: UI-ERROR
Short Syntax: LEC.182 nt net_no:ART entry aging suspnd
Long Syntax: LEC.182 nt net_no:ART entry aging suspended
Description: The ART entries will not be aged out.
| LEC.183 |
Level: U-INFO
Short Syntax: LEC.183 nt network ID:Old llh in func name dscrding: arp_ptr=0x arp_entry_ptr arp_ts= arp_time_stamp vcc_ptr=0x vcc_handle vcc_ts= vcc_time_created
Long Syntax: LEC.183 nt network ID:Old llh in function name discarding:arp_ptr=0x arp_entry_ptr arp_ts= arp_time_stamp vcc_ptr=0x vcc_handle vcc_ts= vcc_time_created
Description: Old llh used in LEC fastpath. A new llh is built.
| LEC.186 |
Level: UE-ERROR
Short Syntax: LEC.186 nt net_no:Jn Rsp cntrl frm err, invld prmtr config_parm
Long Syntax: LEC.186 nt net_no:Join Response control frame error,invalid parameter config_parm
Description: A join response control frame was received. The specified join parm is invalid, or out of range.
| LEC.187 |
Level: C-INFO
Short Syntax: LEC.187 nt net_no:MUF tmr xprd:ntry arp_entry st state
Long Syntax: LEC.187 nt net_no:MUF timer expired:entry arp_entry state state
Description: The Maximum Unknown Frame timer has expired for the specified entry. If the specified state is not CONNECTED or FLUSHING, up to the Maximum Unknown Frame Count of queued frames will be forwarded.
| LEC.188 |
Level: UI-ERROR
Short Syntax: LEC.188 nt net_no:Orphnd MUF tmr xprd:ntry arp_entry st state
Long Syntax: LEC.188 nt net_no:Orphaned MUF timer expired:entry arp_entry state state
Description: An orphaned MUF timer has expired for the specified entry. In the specified state, a MUF timer should not be active.
| LEC.189 |
Level: UI-ERROR
Short Syntax: LEC.189 nt net_no:Fwd Dscn tmr xprd,clnt st err ,st state
Long Syntax: LEC.189 nt net_no:Forward disconnect timer expired,client state error, state state
Description: The forward disconnect timer should not expire for a LEC in this state.
| LEC.190 |
Level: UI-ERROR
Short Syntax: LEC.190 nt net_no:Unbl to strt fwd dscn tmr
Long Syntax: LEC.190 nt net_no:Unable to start forward disconnect timer
Description: The forward disconnect timer could not be started for this LEC.
| LEC.191 |
Level: UE-ERROR
Short Syntax: LEC.191 nt net_no:Reg Rsp err, trans id (x trans_id) not eql rsp trans id (x rsp_trans_id)
Long Syntax: LEC.191 nt net_no:Register Rsp error,trans id (x trans_id) not equal response trans id (x rsp_trans_id)
Description: The transaction id in the register request and register response, was not equal. The transaction id should be the same in the request and response.
| LEC.192 |
Level: UE-ERROR
Short Syntax: LEC.192 nt net_no:Unsuccsfl reg rsp rcvd, LEC trmntd
Long Syntax: LEC.192 nt net_no:Unsuccessful register response received, LEC will be terminated
Description: An unsuccessful register response was received. The LEC's ELAN membership will be terminated.
| LEC.193 |
Level: UI-ERROR
Short Syntax: LEC.193 nt net_no:Regstrtn tmr exceeded, LEC trmntd
Long Syntax: LEC.193 nt net_no:Registration timer exceeded, LEC will be terminated
Description: The registration timer was exceeded. The LEC's ELAN membership will be terminated.
| LEC.194 |
Level: UI-ERROR
Short Syntax: LEC.194 nt net_no:Unbl to xmit reg req, LEC trmntd
Long Syntax: LEC.194 nt net_no:Unable to xmit register request, LEC will be terminated
Description: The LEC was unable to send a register request. The LEC's ELAN membership will be terminated.
| LEC.195 |
Level: U-INFO
Short Syntax: LEC.195 nt net_no:in_use_flag set to TRUE for ARP entry arp_entry
Long Syntax: LEC.195 nt net_no:in_use_flag set to TRUE for ARP entry arp_entry
Description: Based on the domain member response message from the LAN Switch, the in_use_flag for this route descriptor is set to TRUE.
| LEC.196 |
Level: U-INFO
Short Syntax: LEC.196 nt net_no:switch domain member arp_entry, not found in ARP table
Long Syntax: LEC.196 nt net_no:switch domain member arp_entry, not found in ARP table
Description: The switch domain member was not found in the ARP table.
| LEC.197 |
Level: U-INFO
Short Syntax: LEC.197 nt net_no xmit queue hgh wtr mrk, Strt ARP Sweep Timer timer_status
Long Syntax: LEC.197 nt net_no xmit queue high water mark, Start ARP Sweep Timer timer_status
Description: LEC reached high water mark on the transmit buffer queue while trying to transmit an LE_ARP request during the verification or topology sweep timer. The ARP sweep timer is started to finish sending the rest of the outstanding LE_ARPs.
| LEC.198 |
Level: UI-ERROR
Short Syntax: LEC.198 nt network ID:LEC at hgh wtr mrk on xmit buf queue iorbs opfair
Long Syntax: LEC.198 nt network ID:LEC at high water mark on xmit buffer queue iorbs opfair
Description: LEC reached high water mark on the ATM transmit buffer queue while trying to transmit a control frame.
| LEC.199 |
Level: C-INFO
Short Syntax: LEC.199 nt net_no:LE ARP Rqst snt, for LES/BUS tmout, cnt dest_mac, dst count st state
Long Syntax: LEC.199 nt net_no:LE ARP Request sent, for LES/BUS timeout, count dest_mac, dest count state state
Description: An LE ARP request was sent for LES/BUS activity timeout.
| LEC.200 |
Level: C-INFO
Short Syntax: LEC.200 nt net_no:LE ARP Rsp rcvd, for LES/BUS tmout, dest dest_mac st state
Long Syntax: LEC.200 nt net_no:LE ARP Rsp received, for LES/BUS timeout, dest dest_mac state state
Description: An LE ARP response was received for LES/BUS activity timeout.
| LEC.201 |
Level: C_INFO
Short Syntax: LEC.201 nt net_no:updtd cnfgrtn for fld ' field_name'
Long Syntax: LEC.201 nt net_no:updated configuration for field ' field_name'
Description: During initialization, an outdated configuration record was discovered. Certain parameters in the configuration of the LEC were updated to reflect new functional abilities. This event is common after moving to a new code release.
| LEC.202 |
Level: DEBUG
Short Syntax: LEC.202 nt net_no:Inbnd frm dscrd, dst = dest_addr src = src_addr, rsn = reason
Long Syntax: LEC.202 nt net_no:Inbound frame discarded, dest = dest_addr source = src_addr, reason = reason
Description: Inbound frame discarded
| LEC.203 |
Level: UI-ERROR
Short Syntax: LEC.203 nt net_no:LES/BUS tmout, cnt dest_mac, dst count st state
Long Syntax: LEC.203 nt net_no:LES/BUS timeout, count dest_mac, dest count state state
Description: Did not receive a response when sending an LE ARP request. Assuming the LES/BUS are down and resetting the LEC. By resetting, the LEC can find a new LES/BUS.